s-mart UHMWPE (ultra high molecular weight polyethylene)
Symbolbild
- Abkürzung: PE-UHMW
- Deutsch: Polyethylen ultrahochmolekular
- Deutsch: Polyethylen, ultrahohe Molmasse
- high resistance to abrasive wear
- good oxidation resistance
- good sliding and antiadhesive behaviour
- excellent izod impact strength/high resilience at shock and impact stress
- excellent chemical properties; generally recognized as safe for foodstuff applications
- turnability: good
- tool-abrasion: low
Physikalische Eigenschaften
Name | Wert | Sollbereich | Messverfahren und -bedingungen |
---|---|---|---|
Dichte | 0.93 g/cm³ | DIN 53479, 23 °C | |
Mechanische Eigenschaften | |||
Gleitreibungskoeffizient | 0.25 | dry, steel 16MnCr5: v=0,6m/s; p=0,05 MPa; t=5h; 23°C | |
Kugeleindruckhärte | 36 MPa | DIN 53456 H135/30, 23°C | |
Schlagzähigkeit | 130 kJ/m² | ISO 180/1A, Izod, gekerbt | |
Shore-Härte (D) | 61 Shore D | 58 – 64 Shore D | ISO 868, 23 °C |
Zug-Elastizitätsmodul | 680 MPa | DIN 53457, 23 °C | |
Zugdehnung beim Bruch | 50 % | ASTM D 4745-79, 23 °C | |
Zugfestigkeit | 40 MPa | ASTM D 4745-79, 23 °C | |
Thermische Eigenschaften | |||
Einsatztemperatur | -200 – 80 °C | ||
linearer Längenausdehnungskoeffizient | 15 10⁻⁵/K | 25 - 200 °C | |
Wärmeleitfähigkeit | 0.41 (J*10³/(m*h*K) | DIN 52612 |
Chemische Eigenschaften
Name | Wert | Messverfahren und -bedingungen |
---|---|---|
chemische Beständigkeit | mineral oil based: suitable | RT |
mineral oil based: suitable | 60 °C | |
HFA-E water + oil emuls.: suitable | RT | |
HFA-E water + oil emuls: suitable | 60 °C | |
water: suitable | RT | |
water: suitable | 60 °C |
Hersteller
seal-mart GmbH
Dipl. Ing. hans-peter schoeffauer
+4366426477
Anfrage per E-Mail
Webseite | Mehr Details | Zu den Materialien von seal-mart GmbH
Daten bereitgestellt von
seal-mart GmbH
Dipl. Ing. hans-peter schoeffauer
+4366426477
Anfrage per E-Mail
Webseite | Mehr Details | Zu den Materialien von seal-mart GmbH
the mentioned data are only valid for test pieces of the corresponding ISO, DIN and ASTM standards and cannot be directly related to gaskets and joints. the values which are marked with the symbols greater than (≥) and smaller than (≤) are nominal values and must be fulfilled of each batch. all values which are not marked are typical values which are only tested on selected samples.
Ähnliche Materialien
Wählen Sie die Materialeigenschaften aus, anhand derer ähnliche Materialien identifiziert werden sollen. Durch Hinzufügen weiterer Eigenschaften sowie Anpassen der jeweiligen Abweichung lässt sich die Ergebnisliste beeinflussen. Hier wird eine Auswahl der ähnlichsten Materialien angezeigt. Um die gesamte Liste zu erhalten, drücken Sie auf die Schaltfläche "Vollständige Ergebnisliste anzeigen".